Powkiddy RGB30¶
Overview¶
Device | CPU / Architecture | Kernel | GL driver | Interface |
---|---|---|---|---|
RGB30 | Rockchip RK3566 (ARM) | Rockchip BSP 4.19 | Mali | KMS/DRM + Emulation Station |
Features¶
Feature | Notes |
---|---|
Storage | JELOS can be run from an SD Card and an second SD card can be used to store games |
Wifi | Can be turned on in Emulation Station under Main Menu > Network Settings |
Bluetooth | Supports bluetooth audio and controllers |
LED | Supports selecting from a set of colors or turning the power LED off (choice persists through reboots) Does not support other effects. |
Controls¶
RetroArch Hotkeys¶
Button Combo | Action |
---|---|
SELECT+START (x2) | Quit Game |
SELECT+R1 | Save State |
SELECT+L1 | Load State |
SELECT+Y(NORTH) | Open RA Menu |
SELECT+X(WEST) | Show FPS |
SELECT+R2 | Fast-Forward |
Notes:¶
- By default JELOS will detect your controller and configure RetroArch hotkeys automatically. This is controlled by the "AUTOCONFIGURE RETROARCH HOTKEYS" option in the
Settings > Controller & Bluetooth
menu. While the option is enabled, RetroArch hotkeys will be overwritten by the above defaults each time RetroArch is launched. If this behavior is not desired that option can be disabled and your user-defined RetroArch hotkeys will be used instead.
Mednafen Hotkeys¶
Button Combo | Action |
---|---|
SELECT+START (hold for 2sec) | Quit Game |
SELECT+R1 | Save State |
SELECT+L1 (hold for 2sec) | Load State |
SELECT+X(WEST) | Show FPS |
SELECT+R2 | Fast-Forward |
THUMBR+L1 | Select disc |
THUMBR+R1 | Eject/Insert disc |
THUMBR+D-Pad Left | Decrease save slot by 1 |
THUMBR+D-Pad Right | Increase save slot by 1 |
THUMBR+L2 | Configure buttons on virtual port 1 |
Notes:¶
- By default JELOS will expand the configuration file according to the first controller mednafen finds. This only happens when the config file doesn't exist (meaning the first time or if you manually delete it). After the initial expansion you are free to customize the controls.
Mupen64Plus-SA (Nintendo 64)¶
Button Combo | Action |
---|---|
START | Start |
B(EAST) | A |
X(WEST) | B |
Right Analog Up | C Up |
Right Analog Down | C Down |
Right Analog Left | C Left |
Right Analog Right | C Right |
L2 | Z |
L1 | L |
R1 | R |
SELECT+START | Quit Game |
SELECT+R1 | Save State |
SELECT+L1 | Load State |
SELECT+X(WEST) | Take Screenshot |
SELECT+A(SOUTH) | Reset Game |
Notes:¶
- Z and L button assignment can be changed directly in EmulationStation
- Highlight the game and press Y(NORTH)
- Select
ADVANCED GAME OPTIONS
- Set
EMULATOR
toMUPEN64PLUSSA
- Then change
INPUT ONFIGURATION
- Default: L1 = L, L2 = Z
- Z & L SWAP: L1 = Z, L2 = L
- You can also create your own custom controller configuration and add it to
/storage/.configs/game/configs/mupen64plussa
. Then updateINPUT CONFIGURATION
toCUSTOM
following the same steps as above.
PPSSPP-SA (PSP)¶
Button Combo | Action |
---|---|
START | Start |
SELECT | Select |
A(SOUTH) | Circle |
B(EAST) | Cross |
X(NORTH) | Triangle |
Y(WEST) | Square |
L1 | L |
R1 | R |
R2 | Save State |
L2 | Load State |
R3 | Open Menu |
Hypseus-singe (Daphne)¶
Button Combo | Action |
---|---|
SELECT+START | Quit Game |
SELECT | Coin |
START | Start |
A(SOUTH) | Button 1 |
B(EAST) | Button 2 |
Y(NORTH) | Button 3 |
Notes:¶
- To add/change mapping you can edit
/storage/.config/game/configs/hypseus/hypinput.ini
under[KEYBOARD]
section by changing third number for a function from0
(disabled) to a corresponding joystick value. You can identify joystick values by runningjstest /dev/input/js0
over ssh. -
For example the following would assign
quit
to L1 andpause
to R1
Global Hotkeys¶
Button Combo | Action |
---|---|
SELECT+Vol + | Brightness Up |
SELECT+Vol - | Brightness Down |
START+Vol + | Battery Status |
START+Vol - | WIFI Toggle |
HDMI Output¶
These instruction only work for aarm64 devices. This is not implemented for x86_64 devices.
Press L1 + START + SELECT while in EmulationStation to swtich between Screen and HDMI output.
While this should work; it doesn't always result in the correct resolution. The best way to get consistent results is to turn off the device, plug in an HDMI cable and reboot.
"Why doesn't hot-plugging just work?"... Hot-plug HDMI switching is a fairly complex action to accomplish and not something we have implemented on any device. If you are a developer and interested in helping to build this functionality please start here: Contribute
Emulators¶
Notes¶
Installation¶
Video Guide¶
Courtesy of @RetroGameCorps
Download the latest RK3566
version of JELOS from the button below and follow the instructions listed on the Install page. Insert the SD card into the TF-OS slot of the device and power it on.