Loki Max¶
Overview¶
Device | CPU / Architecture | Kernel | GL driver | Interface |
---|---|---|---|---|
Max | Amd Ryzen 7 6800U / (x86_64) | Mainline Linux | Radeonsi | Weston + Emulation Station |
Features¶
Feature | Notes |
---|---|
Storage | JELOS can be run from an SD Card, USB Drive or installed directly to the internal NVME. When installed directly to the NVME; an SD Card can be used for game storage. |
Wifi | Can be turned on in Emulation Station under Main Menu > Network Settings |
Bluetooth | Supports bluetooth audio and controllers |
Fan | Can be set globally, per system or per game. |
TPD Limit | Can be set globally, per system or per game. |
Rumble | Enables the device rumble motor in emulators that support it. |
RGB | Supports selecting from a set of colors and brightness levels or turning the RGB off (choice persists through reboots) Does not support other effects. |
Controls¶
RetroArch Hotkeys¶
Button Combo | Action |
---|---|
SELECT+START (x2) | Quit Game |
SELECT+R1 | Save State |
SELECT+L1 | Load State |
SELECT+Y(NORTH) | Open RA Menu |
SELECT+X(WEST) | Show FPS |
SELECT+R2 | Fast-Forward |
Notes:¶
- By default JELOS will detect your controller and configure RetroArch hotkeys automatically. This is controlled by the "AUTOCONFIGURE RETROARCH HOTKEYS" option in the
Settings > Controller & Bluetooth
menu. While the option is enabled, RetroArch hotkeys will be overwritten by the above defaults each time RetroArch is launched. If this behavior is not desired that option can be disabled and your user-defined RetroArch hotkeys will be used instead.
Mednafen Hotkeys¶
Button Combo | Action |
---|---|
SELECT+START (hold for 2sec) | Quit Game |
SELECT+R1 | Save State |
SELECT+L1 (hold for 2sec) | Load State |
SELECT+X(WEST) | Show FPS |
SELECT+R2 | Fast-Forward |
THUMBR+L1 | Select disc |
THUMBR+R1 | Eject/Insert disc |
THUMBR+D-Pad Left | Decrease save slot by 1 |
THUMBR+D-Pad Right | Increase save slot by 1 |
THUMBR+L2 | Configure buttons on virtual port 1 |
Notes:¶
- By default JELOS will expand the configuration file according to the first controller mednafen finds. This only happens when the config file doesn't exist (meaning the first time or if you manually delete it). After the initial expansion you are free to customize the controls.
Dolphin-SA (Gamecube)¶
Button Combo | Action |
---|---|
SELECT+START | Quit Game |
SELECT+R1 | Save State |
SELECT+L1 | Load State |
SELECT+A(SOUTH) | Screenshot |
SELECT+X(WEST) | Change Internal Resolution |
SELECT+B(EAST) | Change Aspect Ratio |
SELECT+Y(NORTH) | Show FPS |
SELECT+D-Pad Up | Increase current state slot |
SELECT+D-Pad Down | Decrease current state slot |
SELECT+R2 | Fast-Forward |
Mupen64Plus-SA (Nintendo 64)¶
Button Combo | Action |
---|---|
START | Start |
B(EAST) | A |
X(WEST) | B |
Right Analog Up | C Up |
Right Analog Down | C Down |
Right Analog Left | C Left |
Right Analog Right | C Right |
L2 | Z |
L1 | L |
R1 | R |
SELECT+START | Quit Game |
SELECT+R1 | Save State |
SELECT+L1 | Load State |
SELECT+X(WEST) | Take Screenshot |
SELECT+A(SOUTH) | Reset Game |
Notes:¶
- Z and L button assignment can be changed directly in EmulationStation
- Highlight the game and press Y(NORTH)
- Select
ADVANCED GAME OPTIONS
- Set
EMULATOR
toMUPEN64PLUSSA
- Then change
INPUT ONFIGURATION
- Default: L1 = L, L2 = Z
- Z & L SWAP: L1 = Z, L2 = L
- You can also create your own custom controller configuration and add it to
/storage/.configs/game/configs/mupen64plussa
. Then updateINPUT CONFIGURATION
toCUSTOM
following the same steps as above.
PPSSPP-SA (PSP)¶
Button Combo | Action |
---|---|
START | Start |
SELECT | Select |
A(SOUTH) | Circle |
B(EAST) | Cross |
X(NORTH) | Triangle |
Y(WEST) | Square |
L1 | L |
R1 | R |
R2 | Save State |
L2 | Load State |
R3 | Open Menu |
PCSX2-SA (PS2)¶
Button Combo | Action |
---|---|
SELECT+START | Quit Game |
SELECT+R1 | Save State |
SELECT+L1 | Load State |
SELECT+Y(NORTH) | Open Menu |
SELECT+B(EAST) | Take Screenshot |
SELECT+R2 | Fast-Forward |
Hypseus-singe (Daphne)¶
Button Combo | Action |
---|---|
SELECT+START | Quit Game |
SELECT | Coin |
START | Start |
A(SOUTH) | Button 1 |
B(EAST) | Button 2 |
Y(NORTH) | Button 3 |
Notes:¶
- To add/change mapping you can edit
/storage/.config/game/configs/hypseus/hypinput.ini
under[KEYBOARD]
section by changing third number for a function from0
(disabled) to a corresponding joystick value. You can identify joystick values by runningjstest /dev/input/js0
over ssh. -
For example the following would assign
quit
to L1 andpause
to R1
Global Hotkeys¶
Button Combo | Action |
---|---|
SELECT+Vol + | Brightness Up |
SELECT+Vol - | Brightness Down |
START+Vol + | Battery Status |
START+Vol - | WIFI Toggle |
HDMI Output¶
These instruction only work for aarm64 devices. This is not implemented for x86_64 devices.
Press L1 + START + SELECT while in EmulationStation to swtich between Screen and HDMI output.
While this should work; it doesn't always result in the correct resolution. The best way to get consistent results is to turn off the device, plug in an HDMI cable and reboot.
"Why doesn't hot-plugging just work?"... Hot-plug HDMI switching is a fairly complex action to accomplish and not something we have implemented on any device. If you are a developer and interested in helping to build this functionality please start here: Contribute
Notes¶
Installation¶
Download the latest AMD64
version of JELOS from the button below and follow the instructions listed on the Install page.
Booting from an SD Card¶
In order to launch JELOS from an SD card or a USB drive you will need to first change the boot order in the BIOS.
During boot you can enter the bios by either (1) holding the Home+LCC (Turbo) buttons that sit bellow the dpad and right analog stick OR (2) connecting an external keyboard and pressing the Del key.
In the bios; navigate to the Boot
menu and then change the boot order to prioritize the SD card or USB Drive under Boot Order Priorities
. Then go Save & Exit
and select the Save Changes and Exit option. This change will persist through all reboots. If you want to boot into Windows simply remove the SD Card or USB drive.
Changing the RGB¶
In EmulationStation press the Start button to open the Main Menu. Then select System Settings
and scroll until you see Device LEDS
. Under that setting you can choose to turn RGB Off or select from a set of pre-defined colors. The value you set will persist through all future reboots but note your RGB setting will only take effect after JELOS boots.
Development Notes¶
DMI
Info¶
DMI_SYS_VENDOR | DMI_PRODUCT_NAME |
---|---|
ayn |
Loki Max |
Output from evtest
¶
Main Controls
Input driver version is 1.0.1
Input device ID: bus 0x3 vendor 0x45e product 0x28e version 0x110
Input device name: "Microsoft X-Box 360 pad"
Supported events:
Event type 0 (EV_SYN)
Event type 1 (EV_KEY)
Event code 304 (BTN_SOUTH)
Event code 305 (BTN_EAST)
Event code 307 (BTN_NORTH)
Event code 308 (BTN_WEST)
Event code 310 (BTN_TL)
Event code 311 (BTN_TR)
Event code 314 (BTN_SELECT)
Event code 315 (BTN_START)
Event code 316 (BTN_MODE)
Event code 317 (BTN_THUMBL)
Event code 318 (BTN_THUMBR)
Event type 3 (EV_ABS)
Event code 0 (ABS_X)
Value 0
Min -32768
Max 32767
Fuzz 16
Flat 128
Event code 1 (ABS_Y)
Value 0
Min -32768
Max 32767
Fuzz 16
Flat 128
Event code 2 (ABS_Z)
Value 0
Min 0
Max 255
Event code 3 (ABS_RX)
Value 0
Min -32768
Max 32767
Fuzz 16
Flat 128
Event code 4 (ABS_RY)
Value 0
Min -32768
Max 32767
Fuzz 16
Flat 128
Event code 5 (ABS_RZ)
Value 0
Min 0
Max 255
Event code 16 (ABS_HAT0X)
Value 0
Min -1
Max 1
Event code 17 (ABS_HAT0Y)
Value 0
Min -1
Max 1
Event type 21 (EV_FF)
Event code 80 (FF_RUMBLE)
Event code 81 (FF_PERIODIC)
Event code 88 (FF_SQUARE)
Event code 89 (FF_TRIANGLE)
Event code 90 (FF_SINE)
Event code 96 (FF_GAIN)
LCC (Turbo) Button
Event: time 1695144715.833103, type 4 (EV_MSC), code 4 (MSC_SCAN), value 1d
Event: time 1695144715.833103, type 1 (EV_KEY), code 29 (KEY_LEFTCTRL), value 1
Event: time 1695144715.835045, -------------- SYN_REPORT ------------
Event: time 1695144715.837953, type 4 (EV_MSC), code 4 (MSC_SCAN), value 38
Event: time 1695144715.837953, type 1 (EV_KEY), code 56 (KEY_LEFTALT), value 1
Event: time 1695144715.833103, -------------- SYN_REPORT ------------
Event: time 1695144715.835045, type 4 (EV_MSC), code 4 (MSC_SCAN), value 2a
Event: time 1695144715.835045, type 1 (EV_KEY), code 42 (KEY_LEFTSHIFT), value 1
Event: time 1695144715.837953, -------------- SYN_REPORT ------------
Event: time 1695144715.840035, type 4 (EV_MSC), code 4 (MSC_SCAN), value 14
Event: time 1695144715.840035, type 1 (EV_KEY), code 20 (KEY_T), value 1
Quirks¶
- Device Quirks (shares the same quirks as the Loki Zero)
- Panel Rotation